Godaddy Blames Outage On Corrupted Router Tables | Pcworld

Build This Simple Router Jig and Mill Your Own Molding On-Site – Fine Homebuilding

This outage impacted not only users of GoDaddy’s own Web hosting and email services, but also many Web sites with domain names registered through GoDaddy but hosted elsewhere, due to the fact that such websites were primarily located by consulting GoDaddy’s Domain Name System (DNS) servers. GoDaddy maintains records for over 53 million domain names, according to the company. GoDaddy’s outage took place shortly after 10 a.m. PDT Monday and service was fully restored by 4 p.m. PDT, according to the company.
For the original version including any supplementary images or video, visit http://www.pcworld.com/article/262142/godaddy_blames_outage_on_corrupted_router_tables.html

Router vendors responding to growing attacks – E & T Magazine

Anthony Grierco

Keep in mind that overtightening a collet can ruin it. This can be a real problem with cheaper tools where the collet is machined in the motor shaft–it can’t be replaced. Bit By Bit You buy a router to make decorative moldings and to cut joints. But by itself, all it’ll make is noise. Before you leave the store, pick up a few basic bits to get started.
For the original version including any supplementary images or video, visit http://www.popularmechanics.com/home/how-to-plans/woodworking/4230661

This supplements the configuration guides for individual products and covers AAA, RADIUS and TACACS/TACACS+ configuration, password selection and configuration file security, as well as limiting remote access to specific IP addresses using ACLs and VLAN segregation to stop brute force attacks. Earlier this year Brocade announced new port modules for its MLXe router which support Layer 3 256bit IPSec for IP networks and Layer 2 128bit MACsec encryption within the Ethernet link layer. This allows service providers to encrypt data traversing private MPLS or fibre WAN links, which connect business campus networks to the telco core, or handle traffic between data centres, if not necessarily the public Internet. While it does not protect the router itself from attack, it does bestow an extra layer of security on the data traffic that’s passing through the device. Cisco: hardware security ‘bake-in’ If you’re a hacker with a penchant for targeting internetwoking routers, and you like to aim high, then technology from Cisco Systems will be in your sights. Cisco itself concedes that it is having to deal with a fast-growing number of attacks on infrastructure built on its router product lines, reflected, for instance, in an increase in the number of patches issued to fix vulnerabilities identified in its IOS that runs on all its routers, switches, and other networking hardware devices.
For the original version including any supplementary images or video, visit http://eandt.theiet.org/magazine/2014/05/the-protectors.cfm

Using the Dremel Shaper/Router Table and Conclusion | bit-tech.net

Dremel Shaper / Router Table Review Using the Dremel Shaper/Router Table and Conclusion

Then I used a hole saw to bore a 1-1/2-in.-dia. hole that is offset from the center of the groove. This hole accommodates the router bit, and it should be to the left of the groove as you face the jig. This is to ensurethat the router bit, which turns clockwise, will be turning into the work as you feed the stock into it. Next, I bored a similar hole in the top of my job-site workbench to allow the wood chips an escape route. I positioned my router over the hole in the jig and anchored the router to the table with a pair of clamps. The clamps were arranged on opposite sides of the router’s base, in line with the groove in the 2x stock.
For the original version including any supplementary images or video, visit http://www.finehomebuilding.com/item/14188/build-this-simple-router-jig-and-mill-your-own-molding-on-site

7 New Workshop Routers: Comparison Test and Buyer’s Guide – Popular Mechanics

Leaving the rotary tool and cutting bit to do most of the work, we didnt see any signs of flaws in the cuts due to tool movement; so long as you dont apply too much pressure, the Router / Shaper is able to provide clean, accurate cuts. Conclusion In reality, calibrating the Dremel Router / Shaper proved to be a bit of a pain, but its likely youll only have to do this once each time you come to do some routing. For sanding and shaping, it provides both a sturdy mount for your rotary tool, and an effective means of using sanding bands as well as a modest-sized worktable for these tasks. The build quality and instructions arent going to win any awards, and wed prefer if a small selection of cutting and sanding bits were included, but for the price we can t really argue with the latter. The real question is how often youll be using it, and how intense the work will be.
For the original version including any supplementary images or video, visit http://www.bit-tech.net/modding/2012/03/13/dremel-shaper-router-table-review/2